{"id":21978,"date":"2014-05-12T13:30:19","date_gmt":"2014-05-12T17:30:19","guid":{"rendered":"https:\/\/blogs.solidworks.com\/solidworksblog\/?p=21978"},"modified":"2014-05-13T11:24:06","modified_gmt":"2014-05-13T15:24:06","slug":"effectively-running-a-harmonic-analysis-in-solidworks-simulation","status":"publish","type":"post","link":"https:\/\/blogs.solidworks.com\/solidworksblog\/2014\/05\/effectively-running-a-harmonic-analysis-in-solidworks-simulation.html","title":{"rendered":"Effectively Running a Harmonic Analysis in SOLIDWORKS Simulation"},"content":{"rendered":"

One of the most powerful capabilities in SOLIDWORKS Simulation Premium<\/a> is linear dynamics.\u00a0 It encompasses a subset of dynamic analysis that is common in many industries, and can include the following types of analyses: transient, harmonic, random vibration and shock response spectrum analysis.\u00a0 The intent of this blog post is to give you a solid footing and procedure to walk through when you are required to run a harmonic analysis.\u00a0 Let\u2019s first start with a description of exactly what linear dynamics means.<\/p>\n

With linear dynamic analysis, the loads are applied with respect to time or frequency, they can be defined in a deterministic nature (periodic or non-periodic) or non-deterministic, which means they are not precise but defined statistically.\u00a0 Unlike linear static analysis, where only the stiffness, displacement and load are important, with a full linear dynamic system now the damping and mass matrices are included in the equations of motion.<\/p>\n

\"\"<\/p>\n

The stiffness, damping and mass matrices are fixed with respect to time.\u00a0 No material nonlinearity can be included, and there can\u2019t be changes in contact, things can either be bonded or free, otherwise the stiffness of the structure would change.\u00a0 Finally, small deflection theory is required.\u00a0 If any of those criteria are not met, we would need to move from linear dynamics to non-linear dynamic analysis, which is also available in SOLIDWORKS Simulation Premium.<\/p>\n

Harmonic analysis assumes that the applied loads vary as a sine or cosine function.<\/p>\n

Example<\/b>: A reciprocating pump, weighing 150lb, is mounted at the middle of a steel plate of thickness 0.5 in., width 20in., and length 100 in., clamped along two edges. During operation of the pump, the plate is subjected to a harmonic force,<\/p>\n

\"\"<\/p>\n

Our engineering challenge is to find the amplitude of vibration of the steel plate (Reference: Rao 199<\/i>).<\/p>\n

\"\"<\/p>\n

The approach I like to follow is to first solve a modal analysis problem and\/or a static deflection problem.\u00a0 For this example we can do both very quickly, but first let\u2019s investigate the assumptions made in the referenced text to solve this problem.\u00a0 The plate is modeled as a clamped-clamped beam, and the weight is neglected.\u00a0 The material properties for the beam are assumed to be E=30E6 psi.\u00a0 Using these assumptions, we can come up with the closed form solution to this problem.<\/p>\n

Solution:<\/b> The bending stiffness of the beam is given by<\/p>\n

\"\"<\/p>\n

The amplitude of the harmonic response is given by the following equation (Eq 3.6 Rao<\/i>):<\/p>\n

\"\"<\/p>\n

With Fo<\/sub> = 50 lb, and m = 150\/386.4 lb-sec2<\/sup>\/in.<\/p>\n

\"\"<\/p>\n

The negative sign indicates that the response X(t) of the plate is out of phase with the excitation F(t).<\/p>\n

Now let\u2019s walk run this with SOLIDWORKS Simulation.\u00a0 First we model the plate, and at the center we can put a 1 in3<\/sup> block. \u00a0We customize the materials so the plate has the appropriate modulus with a density of nearly zero (as the mass has been neglected in the referenced text).\u00a0 By making the block 1 in3<\/sup> we can input density as 150lbf\/in3<\/sup>.<\/p>\n

\"\"<\/p>\n

Let\u2019s now solve for static deflection and frequency.<\/p>\n

\"\"<\/p>\n

\"\"<\/p>\n

Finally, we setup and run our harmonic analysis.\u00a0 The harmonic force definition gives us the excitation frequency as 62.832 rad\/sec, which correlates to 10 Hz.\u00a0 With linear dynamic studies we are required to run a modal analysis first, and the modes and the mass participation of those modes drive the accuracy of the linear dynamic analysis.\u00a0 For a case like where we are driving the model in the y-direction you want enough modes to get 90% of the mass in the driving axis.\u00a0 You can check this when you run your modal analysis by looking at the mass participation table.<\/p>\n

\"\"<\/p>\n

So, we have 93% of the mass in the y-axis if we pull 20 modes, more than adequate for this run.\u00a0 We\u2019ll also need input some damping; normally we use modal damping and a damping ratio.\u00a0 SOLIDWORKS Simulation<\/a> also allows for Rayleigh (?-?) damping, or you can enter damping in the material properties.\u00a0 In this case, since damping isn\u2019t specified in the referenced text we input the smallest possible damping 1E-5 ratio.<\/p>\n

\"\"<\/p>\n

The final input is just the force. With harmonic analysis any loads you apply are assumed to be applied harmonically.\u00a0 In this case we have a 50 lbf load applied on mass. The amplitude of displacement at 10 Hz is then 0.15 in:<\/p>\n

\"\"<\/p>\n

So, we can see when the problem is characterized correctly the correlation between closed form and FEA solution is very close.<\/p>\n\n\n\n\n\n\n
<\/td>\n\n

Closed Form (Rao)<\/p>\n<\/td>\n

\n

FEA (SOLIDWORKS Simulation)<\/p>\n<\/td>\n<\/tr>\n

\n

Static Deflection (in)<\/p>\n<\/td>\n

\n

0.125<\/p>\n<\/td>\n

\n

0.1251<\/p>\n<\/td>\n<\/tr>\n

\n

Resonant Frequency (Hz)<\/p>\n<\/td>\n

\n

8.845<\/p>\n<\/td>\n

\n

8.843<\/p>\n<\/td>\n<\/tr>\n

\n

Harmonic Response @ 10 Hz (in)<\/p>\n<\/td>\n

\n

0.1504<\/p>\n<\/td>\n

\n

0.1497<\/p>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

 <\/p>\n

There are three other types of linear dynamic studies which will be covered in future blogs; linear transient, random vibration and shock response spectrum. The procedures to effectively run those are similar to harmonic, but they all have their little intricacies. If you have any questions reach out to the technical resources at your resellers<\/p>\n","protected":false},"excerpt":{"rendered":"

One of the most powerful capabilities in SOLIDWORKS Simulation Premium is linear dynamics.\u00a0 It encompasses a subset of dynamic analysis that is common in many industries, and can include the following types of analyses: transient, harmonic, random vibration and shock<\/p>\n... Continued<\/a>","protected":false},"author":175,"featured_media":21979,"comment_status":"open","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"footnotes":""},"categories":[18,63],"tags":[],"class_list":["post-21978","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-solidworks","category-solidworks-simulation"],"acf":[],"_links":{"self":[{"href":"https:\/\/blogs.solidworks.com\/solidworksblog\/wp-json\/wp\/v2\/posts\/21978","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/blogs.solidworks.com\/solidworksblog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/blogs.solidworks.com\/solidworksblog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/blogs.solidworks.com\/solidworksblog\/wp-json\/wp\/v2\/users\/175"}],"replies":[{"embeddable":true,"href":"https:\/\/blogs.solidworks.com\/solidworksblog\/wp-json\/wp\/v2\/comments?post=21978"}],"version-history":[{"count":0,"href":"https:\/\/blogs.solidworks.com\/solidworksblog\/wp-json\/wp\/v2\/posts\/21978\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/blogs.solidworks.com\/solidworksblog\/wp-json\/wp\/v2\/media\/21979"}],"wp:attachment":[{"href":"https:\/\/blogs.solidworks.com\/solidworksblog\/wp-json\/wp\/v2\/media?parent=21978"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/blogs.solidworks.com\/solidworksblog\/wp-json\/wp\/v2\/categories?post=21978"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/blogs.solidworks.com\/solidworksblog\/wp-json\/wp\/v2\/tags?post=21978"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}